[  464.252152] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: all 24 failed cases match known bad, skipping retry
[  464.252346] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: rc=1 (0.8s)
[  464.252361] nipa-hw-worker: [40/53] Running drivers/net/hw:pause.py
[  464.258228] kselftest: Running tests in drivers/net/hw
[  464.330376] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.363898] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  465.278466] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.282092] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  465.302733] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.313992] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.316262] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.330783] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  465.331854] i40e 0000:e1:00.1 ens1f1np1: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  465.349017] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  466.212893] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  466.216460] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  466.297489] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  466.312388] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  466.317845] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  466.321880] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  466.322707] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  467.251346] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  467.254855] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  467.292103] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  467.303038] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  467.304794] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  467.314456] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  467.318480] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.192807] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.196364] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  468.215066] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.237479] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.242876] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  468.243941] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.244640] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.127320] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX/TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.130875] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  472.292739] 8021q: adding VLAN 0 to HW filter on device ens1f0np0
[  472.303008] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  472.314658] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  472.314666] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  472.350224] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  473.169911] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  473.173421] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  473.203029] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  473.218815] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  473.242977] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  474.104556] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  474.108132] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  474.125893] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  474.144765] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  474.167154] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  475.038927] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  475.042496] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  475.095933] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0