[  461.213409] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: all 24 failed cases match known bad, skipping retry
[  461.213594] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: rc=1 (0.8s)
[  461.213610] nipa-hw-worker: [40/53] Running drivers/net/hw:pause.py
[  461.219666] kselftest: Running tests in drivers/net/hw
[  461.291930] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  461.321072] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  462.245002] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.248512] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  462.269849] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.281158] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.283238] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.297273] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  462.298365] i40e 0000:e1:00.1 ens1f1np1: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  462.315292] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.179428] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.182969] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  463.264941] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.279878] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.284350] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  463.288353] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.289083] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.217836] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.221366] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  464.252224] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.267167] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.271676] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  464.275680] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.276468] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.159320] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.162876] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  465.181443] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.192426] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.194261] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.194917] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.204623] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  466.093673] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX/TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  466.097193] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  469.254021] 8021q: adding VLAN 0 to HW filter on device ens1f0np0
[  469.264280] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.275956] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.275963] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.322087] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  470.136405] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  470.139975] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  470.160999] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  470.177651] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  470.199023] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  471.174737] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  471.178304] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  471.228832] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  471.245924] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  471.275446] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  472.109187] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  472.112736] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  472.130163] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0