[  460.468339] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: all 24 failed cases match known bad, skipping retry
[  460.468515] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: rc=1 (0.8s)
[  460.468530] nipa-hw-worker: [40/53] Running drivers/net/hw:pause.py
[  460.474474] kselftest: Running tests in drivers/net/hw
[  460.546511] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  460.575099] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  461.404900] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  461.408477] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  461.428959] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  461.447938] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  461.451958] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  461.454340] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  461.466373] i40e 0000:e1:00.1 ens1f1np1: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  461.483065] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.339597] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.343220] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  462.361670] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.376601] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.382076] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  462.386095] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  462.386763] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.273967] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.277616] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  463.358346] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.373247] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.378771] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  463.382779] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  463.383540] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.319114] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.322748] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  464.353804] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.364738] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.375231] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  464.376328] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  464.377058] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.253670] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX/TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  465.257252] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  468.421900] 8021q: adding VLAN 0 to HW filter on device ens1f0np0
[  468.431362] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.443762] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.443769] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  468.493010] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  469.296314] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.299948] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  469.335508] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.351517] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  469.370516] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  470.231015] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  470.234530] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  470.253214] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  470.268894] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  470.293513] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  471.165282] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  471.168789] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  471.216681] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0