[  761.326569] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: all 24 failed cases match known bad, skipping retry
[  761.329327] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: rc=1 (2.2s)
[  761.329440] nipa-hw-worker: [40/53] Running drivers/net/hw:pause.py
[  761.475012] kselftest: Running tests in drivers/net/hw
[  762.033617] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  762.076179] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  763.054498] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  763.073245] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  763.202379] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  763.221457] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  763.233292] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  763.288911] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  763.332491] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  764.723368] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  764.727694] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  764.792288] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  764.809071] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  764.827601] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  764.829787] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  764.838425] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  765.754228] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  765.757815] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  765.875541] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  765.899959] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  765.901092] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  765.918884] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  765.928109] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  767.007053] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  767.010841] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  767.126890] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  767.146502] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  767.150792] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  767.164433] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  767.173355] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  768.149360] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX/TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  768.152970] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  771.519306] 8021q: adding VLAN 0 to HW filter on device ens1f0np0
[  771.573679] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  771.614537] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  771.614571] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  771.660122] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  772.607402] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  772.611017] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  772.658144] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  772.781807] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  772.811879] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  773.749460] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  773.753093] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  773.818405] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  773.925251] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  773.955042] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  774.891645] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  774.895350] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  774.944209] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0