[  734.473672] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: all 24 failed cases match known bad, skipping retry
[  734.509556] nipa-hw-worker: [39/53] drivers/net/hw:ntuple.py: rc=1 (2.1s)
[  734.509679] nipa-hw-worker: [40/53] Running drivers/net/hw:pause.py
[  734.629091] kselftest: Running tests in drivers/net/hw
[  735.189558] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  735.228876] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  736.195230] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  736.199532] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  736.264354] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  736.295955] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  736.305222] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  736.331084] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  736.372898] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  737.752773] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  737.756624] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  737.829542] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  737.846845] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  737.864415] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  737.868169] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  737.876640] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  738.791157] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  738.794763] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  738.945121] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  738.967980] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  738.971511] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  738.986238] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  738.994605] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  739.940112] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  739.946384] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  740.050570] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  740.068799] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  740.072426] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  740.087160] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  740.094994] i40e 0000:e1:00.0 ens1f0np0: Only speed and autoneg are supported.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  741.186270] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  741.201360] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: RX/TX
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  744.735264] 8021q: adding VLAN 0 to HW filter on device ens1f0np0
[  744.786484] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  744.855895] i40e 0000:e1:00.0 ens1f0np0: Autoneg did not complete so changing settings may not result in an actual change.
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  744.855926] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  744.896872] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  745.851861] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  745.855467] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  745.944914] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  746.073421] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  746.101430] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  747.097871] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  747.101480] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  747.197617] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  747.328461] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  747.347894] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Down
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  748.343882] i40e 0000:e1:00.0 ens1f0np0: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0
[  748.347880] i40e 0000:e1:00.1 ens1f1np1: NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.1
[  748.451262] i40e 0000:e1:00.0 ens1f0np0: To change autoneg please use: ethtool -s <dev> autoneg <on|off>
 SUBSYSTEM=pci
 DEVICE=+pci:0000:e1:00.0